ABA-1010
DSS SATELLITE RECEIVER BOARD
Compatibility Test Plan
Preliminary
September 1997
Prepared By
Compatibility Test Lab
This page intentionally left blank
Table Of Contents
Introduction
Scope
Objectives
Product Features
Schedule
Facts & Policies
Reference Documents
Test Methodology
Compatibility Testing
Test Deliverables
Test Status Memo
Problem Reporting
Test Summary Report
Pass / Fail Criteria
Risks
Systems & Peripherals To Be Tested
System to be tested
Peripheral Devices to be Tested
SCSI Hard Disk Drives
SCSI CD-ROM Drives
SCSI Tape Drives
SCSI MO & Removable Drives
SCSI Host Adapters to be Tested
RAID Adapters to be Tested
BridgeRAID Adapters to be Tested
Operating Systems to be tested
Application Software to be tested
Device Drivers to be tested
Test Configurations
Testing Environment
Novell or NT File Server Configuration
Novell or NT Workstation Configuration
Test Description
Compatibility Test Description
Hardware Compatibility
Software Compatibility
SYSTEM CONFIGURATION
Server Configuration
Workstation Configuration
SCSI Host Adapter Tested
RAID/BridgeRAID Adapter Tested
Peripherals Tested
SCSI Agents Test Cases
Test Descriptions of CI/O SNMP SCSI Agent
Functional Test
Compatibility Test
Test Procedure
Single Control Configuration
Test Cases for Windows NT
Test Cases for Novell NetWare
Test Cases for SCO OpenSever
Test Cases for SCO UnixWare
Multiple Controller Configuration
Results
History log
Introduction
This is the Test Plan for the ABA-1010 DSS Satellite Receiver Board, its related drivers and software, and the ABA-1090 Smart Card Reader. ... It inputs RF signal from a DSS outdoor unit which consists of a satellite dish and low-noise block (LNB) converter. ...
Scope
The purpose of this Test Plan is to describe ABA-1010 DSS Satellite Receiver Board’s testing coverage and methodologies. ...
Objectives
The objectives of CTL testing is to ensure that ABA-1010 DSS Satellite receiver board and its drivers work well together under different hardware platforms, Operating Systems and device configurations. ...
Short PCI card
Board Feature
Schedule
The status and test schedule for this project will be as follows:
Action Estimated Start Estimated Completion Test Time
Compatibility Test 10-9-97 10-22-97 2 weeks
Facts & Policies
This test plan defines the scope of testing to be performed on the ABA-1010 DSS Satellite Receiver Board. ... 23 PA Intel 430LX
Peripheral Devices to be Tested
SCSI hard disk drives will be randomly selected from the following list for testing and setting up NetWare and Windows NT servers to test the Adapted CI/O applications module. ...
TC#14 Remove a drive from the AHA-2940 (just remove the power plug, leave the system up and running) and confirm that the device display is correct. ...
TC#15 Add the same drive to the AHA-2940 (while the system is up and running) and confirm that the device display is updated correctly. ...
Remove a drive from the AAA-13x bus (just remove the power plug, leave the system up and running), run rescan and confirm that the device display is correct. ...
Add a drive to the AAA-13x bus (while the system is up and running), run rescan and confirm that the device display is correct. ...
Move the CD-ROM from the AAA-13x bus to the AHA-2940 bus (leave the system up and running), and confirm that the icon device display is correct within the thirty minute period. ...
Add a tape unit to the AHA-2940 bus and confirm that the icon device display is correct (remember the 30 minute, default, time setting). ...
Boot-up and initialization
This test is done to verify the proper initialization of the IOMGR and SNMP SCSI agent under each version of the network Operating System (NOS). ...
Step 5: Set up a remote client with either Windows 95 or Windows NT workstation
Step 6: Attach a remote client to the server using TCP/IP protocol. ...
Step 5: Set up a remote client with either Windows 95 or Windows NT workstation
Step 6: Attach a remote client to the server using TCP/IP protocol. ...
Step 5: Set up a remote client with either Windows 95 or Windows work group v3. ...
Step 5: Set up a remote client with either Windows 95 or Windows workgroup v3. ...
Step 6: Set up a remote client with either Windows 95 or Windows work group v3. ...
Step 6: Set up a remote client with either Windows 95 or Windows workgroup v3. ...
Step 6: Set up a remote client with either Windows 95 or Windows work group v3. ...
Step 6: Set up a remote client with either Windows 95 or Windows for workgroup. ...
Step 6: Set up a remote client with either Windows 95 or Windows NT workstation
Step 7: Attach a remote client to the server using TCP/IP protocol. ...
Step 5: Set up a remote client with either Windows 95 or Windows workgroup v3. ...
Step 6: Set up a remote client with either Windows 95 or Windows workgroup v3. ...
Step 6: Set up a remote client with either Windows 95 or Windows v3.
To link to this page, copy the following code to your site:
All Papers Are For Research And Reference Purposes Only!
You may not turn these papers in as your own! You must cite our web site as your source!
